Volatile Organic Compounds (VOCs)

Volatile Organic Compounds (VOCs)

Volatile Organic Compounds (VOCs): Volatile Organic Compounds are toxic organic chemicals with higher tendencies to change from liquid to vapor phase under typical earth pressures and temperatures, and usually have little-to-no water solubility characteristics. VOCs are commonly found within hydrocarbon-based fuel additives, industrial solvents, refrigerants, hydraulic fluids, degreasers, and more. These compounds are generally known to be toxic, and result in adverse health effects upon human exposure. For instance, a liquid-phase tetrachloroethene (PCE) contamination plume may volatilize over time, creating a soil vapor intrusion scenario to the buildings aboveground. As a result, workers inside the building become exposed to the colorless and odorless VOC, in the form of vapor inhalation.

VOCs Soil & Groundwater Contamination

When a Phase 1 Environmental Site Assessment reveals “recognized environmental conditions,” professional geologists test the subsurface for VOC soil contamination. Environmental Protection Agency (EPA) Laboratory Analysis Method 8260B applies to test soil and groundwater samples underlying fuel underground storage tanks (UST), dry cleaners, underground hydraulic lifts, waste oil tanks, etc.

Phase 2 Environmental Site Assessments and Indoor Air Quality Tests can help identify VOC contamination. Afterward, each volatile organic compound detection is run across the applicable screening level. And Human Health Risk Assessments aim to determine toxicity thresholds upon exposure.

If soil and groundwater contamination is present, a remedial action plan aims to clean up the soil contamination at the source. Lastly, impervious vapor barriers mitigate VOC pollution hazards to building occupants during and after remediation. 

EPA List of Volatile Organic Compounds (VOCs)

The following list provides the names of each volatile organic compound on the EPA list, per EPA Laboratory Method 8260B.

  • Dichlorodifluoromethane
  • Chloromethane
  • Vinyl Chloride
  • Bromomethane
  • Chloroethane
  • Trichlorofluoromethane
  • Freon 113
  • 1,1-Dichloroethene
  • Iodomethane
  • Methylene Chloride
  • trans-1,2-Dichloroethene
  • 1,1-Dichloroethane
  • 2,2-Dichloropropane
  • cis-1,2-Dichloroethene
  • Bromochloromethane
  • Chloroform
  • 1,2-Dichloroethane
  • 1,1,1-Trichloroethane
  • Carbon tetrachloride
  • 1,1-Dichloropropene
  • BTEX
    • Benzene
    • Toluene
    • Ethylbenzene
    • Xylenes
  • Tetrachloroethene (PCE)
  • Trichloroethene (TCE)
  • 1,2-Dichloropropane
  • Bromodichloromethane
  • Dibromomethane
  • Trans-1,3-Dichloropropene
  • cis-1,3-Dichloropropene
  • 1,1,2-Trichloroethane
  • 1,3-Dichloropropane
  • Dibromochloromethane
  • 2-Chloroethylvinyl ether
  • Bromoform
  • Isopropylbenzene
  • Bromobenzene
  • 1,2-Dibromoethane (EDB)
  • Chlorobenzene
  • 1,1,1,2-Tetrachloroethane
  • Styrene
  • 1,1,2,2-Tetrachloroethane
  • 1,2,3-Trichloropropane
  • n-Propylbenzene
  • 2-Chlorotoluene
  • 4-Chlorotoluene
  • 1,3,5-Trimethylbenzene
  • tert-Butylbenzene
  • 1,2,4-Trimethylbenzene
  • Sec-Butylbenzene
  • 1,3-Dichlorobenzene
  • p-Isopropyltoluene
  • 1,4-Dichlorobenzene
  • 1,2-Dichlorobenzene
  • n-Butylbenzene
  • 1,2,4-Trichlorobenzene
  • 1,2-Dibromo-3-Chloropropane
  • Hexachlorobutadiene
  • Naphthalene
  • 1,2,3-Trichlorobenzene
  • Acetone
  • 2-Butanone (MEK)
  • 4-Methyl-2-pentanone (MIBK)
  • 2-Hexanone
  • Vinyl Acetate
  • Ethanol
  • Methyl tert-butyl ether (MTBE)
  • Ethyl Tertiary Butyl Ether (ETBE)
  • N,N-Diisopropylethylamine (DIPE)
  • tert-Amyl methyl ether (TAME)
  • T-Butyl Alcohol

Similar Posts

  • Milliequivalent per liter

    ByGeo Forward

    Milliequivalent per liter Milliequivalent per liter (meq/L): A unit used to express the chemical equivalence of the concentration of solutes in a solution. It is calculated by dividing the concentration of a substance (in mg/L) by its equivalent weight. This measurement helps in understanding the reactive capacity of ions in the solution.

  • Potentiometric Surface

    ByGeo Forward

    Potentiometric Surface The term “Potentiometric Surface” means the hydrogeological surface that represents the total hydraulic head of groundwater from a confined aquifer or semi-confined aquifer that’s under pressure. The Potentiometric Surface of an aquifer is defined by the level to which water will rise in a groundwater monitoring well (that’s exclusively screened within said aquifer).

  • Liquid Limit (LL)

    ByGeo Forward

    Liquid Limit (LL) “Liquid Limit (LL)” in the field of geological engineering, refers to the upper limit of the “plastic state.” This is a separation of the plastic phase and viscous liquid phase when measuring soil consistency. Mathematically, it is the water content (basing on the percent of dry weight), at which two sections of…

  • Aphanitic

    ByGeo Forward

    Aphanitic Definition Aphanitic: In geology, the term aphanitic describes the texture of plutonic or volcanic igneous rocks, with grains that are not visible to the naked eye. In fact, an aphanitic texture is usually the result of faster cooling and solidification of liquid magma.

  • Gap-Graded

    ByGeo Forward

    Gap-Graded The term “Gap-Graded” is used by geologists, engineers, and soil scientists in the geotechnical engineering field to describe the gradation of a soil sample, specifically when some particle sizes are missing. Aside from being “gap graded,” a soil sample can be described as “well-graded” (also referred to as poorly sorted), or “poorly graded” (or…

  • Terrestrial Planet Definition

    ByGeo Forward

    Terrestrial Planet Definition A terrestrial planet is any planet in the universe that has earth-like composition, such as rocks, and other similar solid substances. For instance, Mars is a terrestrial planet in our solar system, whereas Jupiter is not. This is because modern geologists, astrophysicists, and astronomers understand Mars to contain solid formations correlative to…